For Arctic Cat Pro Climb/Cross snowmobiles – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Pieces C & D are the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.

For Arctic Cat M-Series snowmobiles – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Pieces 1, 7 and 9 are the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.

For Arctic Cat Sno Pro Race Chassis snowmobiles – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Pieces 2, 9 and 10 are the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.

For Arctic Cat Sno Pro snowmobiles – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Pieces 1, 2 and 3 are the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.

For Polaris PRO RMK/Rush snowmobiles – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Pieces 25, 26, 40 and 41 are the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.

For Polaris RMK/Dragon snowmobiles – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Pieces 1, 2, 8 and 9 are the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.

For Polaris IQ Race Chassis snowmobiles – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Piece 1 is the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.

For Ski-Doo Rev XP/E-Tec Models – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Pieces 8, 9, 18, 19 and 20 are the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.

For Ski-Doo Rev snowmobiles – Start with the side panel decals and finish with the hood/console decals.  The provided installation guide will help you sort through the Print Layout so that there is no confusion on which pieces go where.

Pieces 1, 9, 11 and 12 are the most difficult to install.  We recommend cutting these pieces out from the overall print so that the backing is still on them.  From there, place the piece on the hood and align properly.  Once alignment is correct, use masking tape to set in place.  Run a long piece of masking tape down the center of the piece, acting as a hinge.  Lift one half of the decal up and remove the backing material and cut away.  Once that is away, hold the piece with slight tension and work onto hood center outward.  This will prevent air bubbles and ensure a proper adhesion.  Remember to take your time and have patience.